25W non flickering 1-10V / PUSH dimming LED power supply Energy saving
Description:
1, 5-year warranty
2, Dim via a potentiometer
3, Stand-by power below 0.5W
4, Primary dimming with PUSH Button
5, Secondary dimming with 1-10V dimmer
6, Flicker-free for whole dimming range
7, Support Master-Slave grouping net-working
8, Dimming level memory at mains restores
9, Derating current for over high ambient temperature
10, Protection: Short circuit/ Over temperature/ Over voltage
11, Maximum length of the cable, from push button to last driver is 20m
Specifications
| INPUT | Input voltage | 220-240Vac |
| Input frequency | 50-60Hz |
| Input current | 0.14A max |
| Power factor (Note 1) | ≥0.90 |
| Efficiency(Note1) | ≥80% |
| Stand-by power (Note 2) | ≤0.5W |
| OUTPUT | Output current/ voltage | 250mA 6~58Vdc 14.5W max; 350mA 6~58Vdc 20W max 500mA 6~50Vdc 25W max; 700mA 6~36Vdc 25W max |
| Output load range | 25.2W Max. |
| Current accuracy | ±5% |
| Dimming mode | 1-10V, PUSH |
| ENVIRONMENT | Working temp.(Ta) | -20~50℃ |
| Surface temp.(Tc) | 85℃max |
| Working humidity | 20~85%RH non-condensing |
| Storage temp. | -40~80℃ |
| Life time | ≥50000hours |
| PROTECTION | Isolation class | Class Ⅱ, SELV |
| Protection class | IP20 |
| Over voltage | 300Vac, 2H |
| Short circuit | Protection type; auto reset |
| No-load | Protection type; auto reset |
| Over temperature | Protection type; auto reset |
| OTHERS | Safety | EN61347-1 EN61347-2-13 |
| EMC | EN55015, EN61000-3-2 |
| EN61000-3-3, EN61547 |
| Approvals | SEMKO, CE, RoHS |
| Withstand voltage | IN-OUT:3.75KVAC/5mA/1min |
| Dimension (L x W x H) | 150x52x28mm |
| Connection | Press-in type terminals, 0.75-1.5mm2 Input: L,L,N,N,PUSH,PUSH,Sync,Sync Output: SEC(+) SEC(-), 1-10V(+),1-10V(-) |
| NOTE | Note: 1, Power factor and efficiency is detected at 230Vac input and full load. 2, Standby power is detected at 230Vac input and switch off led load by push button. |
Mechanical Specification:
Dimming Operation:
1.Push button switch for dimming (see wiring diagram, Fig A & Fig B)
- ON/OFF: Short push (120ms ~ 1sec) on the switch
- Stepless dimming: Long push (＞1sec) on the switch. With every other long push, the light level goes the opposite direction.
- Synchronization: No need additional synchrony wire in larger installation, up to 15pcs drivers when connected to the same switch.
2.1-10V dimming (see wiring diagram, Fig C)
The driver supports any active 1-10V dimmer. When the dimming signal is less than 0.8V ~ 1V or short the dimming wires, the output of LED driver could be completely switch off, see Fig C
Wring Diagram:
Fig.A
Fig.B
Fig.C
Download:
ML25C-PV.pdf
Product Tags:
|
|
25W Non Flickering 1-10V / PUSH Dimming LED Power Supply Energy Saving Images
|
